Erasing Shadows/Lines
16-Dec-2011
8200289500
Solution
This mode enables you to erase shadows and lines that appear when copying. The following three Frame Erase modes are available: Original Frame Erase, Book Frame Erase, and Binding Erase.
The default setting is <Off>.
NOTE
Frame Erase modes cannot be combined. If you select one of these modes, the previously set mode is canceled.
This mode erases the dark borders and frame lines that appear around the copy if the original is smaller than the selected paper size. You can also use this mode to create a blank border around the edge of the copy.
NOTE
The Original Frame Erase mode cannot be used with the N on 1 mode.
1. Set originals.
2. Press 
(Main Menu).
(Main Menu).3. Use [ 
] , [ 
] or 
(Scroll Wheel) to select <Copy>, then press [OK].
] , [ ] or (Scroll Wheel) to select <Copy>, then press [OK].4. Use [ ] , [ ] or (Scroll Wheel) to display <Shadow/Frame Erase Settings>, then press [OK].
] , [ ] or (Scroll Wheel) to display <Shadow/Frame Erase Settings>, then press [OK].5. Use [ ] , [ ] or (Scroll Wheel) to select <Original Frame Erase>, then press [OK].
] , [ ] or (Scroll Wheel) to select <Original Frame Erase>, then press [OK].6. Use [ ] , [ ] , (Scroll Wheel) or 
- 
(numeric keys) to select the original size, then press [OK].
] , [ ] , (Scroll Wheel) or - (numeric keys) to select the original size, then press [OK].NOTE
To switch to the inch sizes, press the left Any key to select <Inch Size>.
7. If you want to set the same width for all four borders, use [ ] , [ ] or (Scroll Wheel) to enter a frame erase width value, then press [OK].
] , [ ] or (Scroll Wheel) to enter a frame erase width value, then press [OK].Proceed to step 12.
NOTE
- The default setting is <6 mm>. The maximum original frame erase width that you can set is <50 mm>.
- To enter values in inch, press the left Any key to select <Enter inch>.
- If you want to change the value, press
(Clear) before entering the new value. - If you enter an invalid value, a message prompting you to enter an appropriate value appears on the screen.
8. If you want to set the top, left, right, and bottom widths independently, press the right Any key to select <Adj. Each Dim.>.
9. Use [ ] , [ ] or (Scroll Wheel) to select the desired frame erase borders, then press [OK].
] , [ ] or (Scroll Wheel) to select the desired frame erase borders, then press [OK].NOTE
To enter values in inch, press the left Any key to select <Enter inch>.
10. Use [ ] , [ ] , (Scroll Wheel) or - (numeric keys) to enter a frame erase width value, then press [OK].
] , [ ] , (Scroll Wheel) or - (numeric keys) to enter a frame erase width value, then press [OK].NOTE
- The default setting is <6 mm>. The maximum original frame erase width that you can set is <50 mm>.
- If you want to change the value, press (Clear) before entering the new value.
- If you enter an invalid value, a message prompting you to enter an appropriate value appears on the screen.
11. Use [ ] , [ ] or (Scroll Wheel) to select Apply Settings>, then press [OK].
] , [ ] or (Scroll Wheel) to select Apply Settings>, then press [OK].The display will return to the Copy top screen.
12. Use - (numeric keys) to enter the desired copy quantity (1 to 99).
- (numeric keys) to enter the desired copy quantity (1 to 99).13. Press 
(Start).
(Start).If you want to copy multiple originals using the platen glass, set an original and press (Start) once for each page.
(Start) once for each page.14. Press (Main Menu) to return to the Main Menu screen.
(Main Menu) to return to the Main Menu screen.This mode erases the dark borders and the center and contour lines that appear when you copy facing pages in a book or bound original onto a single sheet of paper.
NOTE
- The Book Frame Erase mode cannot be used with the N on 1.
- You must place an original on the platen glass when using this function.
1. Set an original on the platen glass.
2. Press (Main Menu).
(Main Menu).3. Use [ ] , [ ] or (Scroll Wheel) to select <Copy>, then press [OK].
] , [ ] or (Scroll Wheel) to select <Copy>, then press [OK].4. Use [ ] , [ ] or (Scroll Wheel) to display <Shadow/Frame Erase Settings>, then press [OK].
] , [ ] or (Scroll Wheel) to display <Shadow/Frame Erase Settings>, then press [OK].5. Use [ ] , [ ] or (Scroll Wheel) to select <Book Frame Erase>, then press [OK].
] , [ ] or (Scroll Wheel) to select <Book Frame Erase>, then press [OK].6. Use [ ] , [ ] or (Scroll Wheel) to select the original size, then press [OK].
] , [ ] or (Scroll Wheel) to select the original size, then press [OK].NOTE
To switch to the inch sizes, press the left Any key to select <Inch Size>.
7. Enter the each erase width value:
8. If you want to specify the erase width value for center, use [ ] , [ ] or (Scroll Wheel) to select <Center>, then press [OK].
] , [ ] or (Scroll Wheel) to select <Center>, then press [OK].NOTE
To enter values in inch, press the left Any key to select <Enter inch>.
9. Use [ ] , [ ] , (Scroll Wheel) or - (numeric keys) to enter a frame erase width value, then press [OK].
] , [ ] , (Scroll Wheel) or - (numeric keys) to enter a frame erase width value, then press [OK].Proceed to step 12.
NOTE
- The default setting is <10 mm>. The maximum original frame erase width that you can set is <50 mm>.
- If you want to change the value, press (Clear) before entering the new value.
- If you enter an invalid value, a message prompting you to enter an appropriate value appears on the screen.
10. If you want to specify the erase width value for all sides, use [ ] , [ ] or (Scroll Wheel) to select <All Sides>, then press [OK].
] , [ ] or (Scroll Wheel) to select <All Sides>, then press [OK].11. Use [ ] , [ ] , (Scroll Wheel) or - (numeric keys) to enter a frame erase width value, then press [OK].
] , [ ] , (Scroll Wheel) or - (numeric keys) to enter a frame erase width value, then press [OK].NOTE
The default setting is <6 mm>. The maximum original frame erase width that you can set is <50 mm>.
12. Use [ ] , [ ] or (Scroll Wheel) to select <Apply Settings>, then press [OK].
] , [ ] or (Scroll Wheel) to select <Apply Settings>, then press [OK].13. Use - (numeric keys) to enter the desired copy quantity (1 to 99).
- (numeric keys) to enter the desired copy quantity (1 to 99).14. Press (Start).
(Start).If you want to copy multiple originals using the platen glass, set an original and press (Start) once for each page.
(Start) once for each page.15. Press (Main Menu) to return to the Main Menu screen.
(Main Menu) to return to the Main Menu screen.This mode erases the shadows that appear on copies from binding holes on originals.
NOTE
- You must place an original on the platen glass when using this function.
- Do not place originals with binding holes into the feeder, as this may damage the originals.
- The borders you do not select are attenuated when using this function.
1. Set an original on the platen glass.
2. Press (Main Menu).
(Main Menu).3. Use [ ] , [ ] or (Scroll Wheel) to select <Copy>, then press [OK].
] , [ ] or (Scroll Wheel) to select <Copy>, then press [OK].4. Use [ ] , [ ] or (Scroll Wheel) to display <Shadow/Frame Erase Settings>, then press [OK].
] , [ ] or (Scroll Wheel) to display <Shadow/Frame Erase Settings>, then press [OK].5. Use [ ] , [ ] or (Scroll Wheel) to select <Binding Erase>, then press [OK].
] , [ ] or (Scroll Wheel) to select <Binding Erase>, then press [OK].6. Use [ ] , [ ] or (Scroll Wheel) to select the original size, then press [OK].
] , [ ] or (Scroll Wheel) to select the original size, then press [OK].NOTE
To switch to the inch sizes, press the left Any key to select <Inch Size>.
7. Use [ ] , [ ] or (Scroll Wheel) (Scroll Wheel) to select the hole punch location, then press [OK].
] , [ ] or (Scroll Wheel) (Scroll Wheel) to select the hole punch location, then press [OK].NOTE
To enter values in inch, press the left Any key to select <Enter inch>.
8. Use [ ] , [ ] , (Scroll Wheel) or - (numeric keys) to select the frame erase width, then press [OK].
] , [ ] , (Scroll Wheel) or - (numeric keys) to select the frame erase width, then press [OK].NOTE
- The default setting is <18 mm>. The maximum original frame erase width that you can set is <20 mm>.
- If you want to change the value, press (Clear) before entering the new value.
- If you enter an invalid value, a message prompting you to enter an appropriate value appears on the screen.
9. Use - (numeric keys) to enter the desired copy quantity (1 to 99).
- (numeric keys) to enter the desired copy quantity (1 to 99).10. Press (Start).
(Start).If you want to copy multiple originals using the platen glass, set an original and press (Start) once for each page.
(Start) once for each page.11. Press (Main Menu) to return to the Main Menu screen.
(Main Menu) to return to the Main Menu screen.