How to perform the wireless LAN setup manually (Macintosh)

    08-Jun-2010
    8200822400

    Solution

    Wireless Setup
    NOTE
    Before connecting the machine to the network, make sure that the computer and access point or router is connected.
    Add (connect) the machine to the network.
    A: Internet
    B: Access point or wireless router, etc.

    - Notes on Wireless Connection
    • The configuration, router functions, setup procedures and security settings of the network device vary depending on your system environment. For details, refer to your device's instruction manual or contact its manufacturer.
    • In an office setup, consult your network administrator.
    • If you connect to a network that is not protected with security measures, there is a risk of disclosing data such as your personal information to a third party.
    • If an error message appears or if you have trouble with the network connection, refer to the printed manual: Network Setup Troubleshooting.
    • Place the machine and computer on the same network segment.
    NOTE
    An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without using an access point, is not supported. Be sure to prepare an access point.

    Wireless Setup Using Easy Setup
    • Check the Information for Wireless Connection
    In most cases, "Easy Setup" will be used to connect the machine to your access point or router. Before you continue, you must gather the information below which will be required during the installation.
    NOTE
    • For details on how to check the following information, refer to the manual of your access point or router, or contact its manufacturer.

    - Access Point Name/Network Name:
    * Also referred to as SSID.
    An identifier to identify the specific access point.

    - Network Key:
    * Also referred to as encryption key, WEP key or WPA/WPA2 passphrase, Pre-Shared key.
    A password required to set to prevent unauthorized access to communication.

    1.
    Use the or button (A) to display Setup, then press the right FUNCTION button (B).

    2.
    Use the or button (C) to select Wireless LAN setup, then press the OK button.

    3.
    Select Yes, then press the OK button.
    When wireless connection is enabled, the Wi-Fi lamp (D) lights blue.

    4.
    Select Easy setup, then press the OK button.

    5.
    Select the access point name you wrote down, then press the OK button.
    NOTE
    • Nearby access points may be detected.
    • The access point names with 2-byte characters are not displayed properly, however, can be selected.

    6.
    Make sure that one of the above screens is displayed, then press the right FUNCTION button.
    If the above screen is not displayed, go to 9.

    7.
    Enter the network key you wrote down on, then press the left FUNCTION button (E).
    Press the center FUNCTION button (F) to switch character entry modes.
    Enter upper and lower case letters of the alphabet correctly.
    NOTE
    - Character Entry
    This machine allows you to enter characters when an on-screen keyboard is displayed.
    Follow the procedure below.
    1. When an on-screen keyboard shown above is displayed, press the center FUNCTION button (F) to switch to a keyboard having characters you want to use.
    • Four character sets are available: Upper-case alphabets, lower-case alphabets, numbers,and symbols. Each time you press the center FUNCTION button, an on-screen keyboard isswitched among them.
    2. Select a character on the on-screen keyboard using the buttons (A)(C),then press the OK button to enter it.
    • Entered characters are displayed on the upper section (G) of the on-screen keyboard.
    3. Repeat (1) and (2) to enter more characters.
    4. After you enter all characters you need, press the left FUNCTION button (E).
    * To insert a space, select Space on the on-screen keyboard and press the OK button.
    * To insert characters, select the section (G) of the screen using the or button, move the cursor to the character on the right of the target position using the or button, then enter characters.
    * To delete a character, select the section (G) of the screen using the or button, move the cursor to the target character using the or button, then press the right FUNCTION button (B).

    8.
    Make sure that the network key is correct, then press the OK button.

    9.
    When the above screen appears, press the OK button.
    NOTE
    • If Failed to connect to the access point. appears, press the OK button, make sure that the network key is correct, then enter it again. If a connection still cannot be established, refer to the printed manual: Network Setup Troubleshooting.

    Install the Software (Network Connection)
    • To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk. The installation process takes about 20 minutes. (The installation time varies depending on the computer environment or the number of application software to be installed.)
    IMPORTANT
    • Quit all applications before installation.
    • Log on as the administrator (or a member of the Administrators group).
    • If the firewall function of your security software displays a warning message, set the security software to always allow access.

    1.
    Turn on the computer, then insert the Setup CD-ROM into the CD-ROM drive.
    If you are using Windows, the setup program starts automatically.

    2.
    Double-click the Setup icon of the CD-ROM folder to proceed to the following screen. Enter your administrator name and password, then click OK.
    If the CD-ROM folder does not open automatically, double-click the CD-ROM icon on the desktop.
    If you do not know your administrator name or password, click the help button, then follow the on-screen instructions.

    3.
    Select your place of residence, then click Next.
    NOTE
    • If the Select Language screen appears, select a language, then click Next.

    4.
    Select a country or region, then click Next.

    5.
    Click Easy Install.
    The drivers, application software, and on-screen manuals are installed.
    NOTE
    • If you want to select particular items to install, click Custom Install.

    6.
    Click Install.

    7.
    Select Use the printer on network, then click Next.
    Follow any on-screen instructions to proceed with the software installation.

    8.
    When the Printer Detection screen appears, click Next.
    NOTE
    • If the Printer Connection screen appears instead of the screen above, the connection method is not correctly selected in 7.
    - Follow on-screen instructions and proceed with the installation. Click Exit on the installation complete screen, then start again from 2 and be sure to select Use the printer on network in 7.

    9.
    On the Canon IJ Network Tool screen, select MG5200 series in Printers, then click Next.
    NOTE
    • If the machine is not detected, refer to the printed manual: Network Setup Troubleshooting. Make sure there is no problem, then click Update.

    Registration
    NOTE
    • The alphanumeric characters after Canon MG5200 series is the machine's Bonjour service name or MAC address.
    • If the machine has not been detected, make sure of the following.
    - The machine is turned on.
    - The firewall function of any security software is turned off.
    - The computer is connected to the access point.

    1.
    When the Register Printer and Scanner screen appears, click Register Printer.
    Mac OS X
    v.10.6.x v.10.5.x -> Go to 2-A
    v.10.4.11 -> Go to 2-B

    2-A Mac OS X v.10.6.x/v.10.5.x
    Mac OS X v.10.4.11 -> 2-B

    (1)
    Select Canon MG5200 series canonijnetwork and click Add.
    -> Go to 3

    2-B Mac OS X v.10.4.11

    (1)
    When the Printer List window appears, click Add.
    NOTE
    • When the You have no printers available. screen appears, click Add.

    (2)
    Click More Printers in the Printer Browser window.

    (3)
    Select Canon IJ Network in the pop-up menu, select Canon MG5200 series in the list of printers, then click Add.

    (4)
    Make sure that Canon MG5200 series is added to the list of printers.

    3.
    When the Register Printer and Scanner screen appears, click Register Scanner.

    4.
    Select Canon MG5200 series on the Scan-from-PC Settings screen, then click OK.

    5.
    Click Next on the Register Printer and Scanner screen.

    Install the Software (Information)
    1.
    Click Next.
    Follow any on-screen instructions to proceed with the software installation.

    - Important Information for the Installation

    • Necessary Information for the User Registration
    When the serial number is not displayed on the registration screen automatically, input the serial number located inside the machine (as shown in the illustration).
    IMPORTANT
    • If the power is on, the Print Head Holder will move when the Scanning Unit (Cover) (A) is opened.
    NOTE
    • The User Registration screen will only be displayed when Europe, Middle East, Africa is selected on the Select Your Place of Residence screen.

    • If the Extended Survey Program screen appears
    If you can agree to Extended Survey Program, click Agree.
    If you click Do not agree, the Extended Survey Program will not be installed.
    (This has no effect on the machine’s functionality.)

    2.
    Click Exit to complete the installation.
    It is necessary to restart the computer before scanning using the Operation Panel on the machine for the first time.

    3.
    Solution Menu EX starts when clicking OK in the Canon Solution Menu EX dialog.
    Remove the Setup CD-ROM and keep it in a safe place.
    NOTE
    • The buttons displayed on Solution Menu EX may vary depending on the country or region of purchase.

    • Using the Machine from Additional Computers
    Now that the wireless connection of the machine is complete, it can be used from additional computers on the same network.
    Install software including the drivers on the computer from which you want to use the machine. Other settings are not required.
    To add computers from which to use the machine, go to [ Use from Additional Computers ]

    Use from Additional Computers
    NOTE
    • If the machine is already connected to a wireless connection, it can be used from additional computers on the same network.

    To use from additional computers

    1. Insert the Setup CD-ROM into the computer from which you want to use the machine.

    2. Follow the on-screen instructions to install the software.
    Other settings are not required.
    A: Computer from which the machine can be used currently
    B: Additional computers on the same network It enables the computer to use the machine.
    NOTE